错误代码 |
错误消息 |
原因及故障排除 |
RYAA001 |
The specified shared memory already exists. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA002 |
The specified shared memory does not exist. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA003 |
A shared memory already exists, but its memory size is less than specified. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA004 |
Cannot create a shared memory due to insufficiency of memory or resource. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA005 |
Could not start TdasEngine because it is already in execution or termination. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA006 |
Could not stop TdasEngine because it is already in suspension or termination. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA007 |
Could not register the operation in TdasEngine. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA008 |
Cannot execute State Transition of TdaInfo because a small service is now in transition. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA009 |
The device name ( **** ) specified as the destination Node does not exist. |
主站和从站人机界面的外接设备规定的名称不同。外接设备的名称必须一致。 |
RYAA010 |
Cannot execute the operation due to the invalid state of the small service. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA011 |
Cannot execute the operation because the small service is not in operation. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA012 |
Cannot execute the operation because the small service is in error suspension. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA013 |
The I/F of an unsupported small service was called. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA016 |
Could not register the item because of insufficient memory. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA017 |
Accessed a device in which no item is registered. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA018 |
Accessed an out-of-range device. |
访问了超出有效范围的寄存器。 |
RYAA019 |
Failed to register the specified cluster because an invalid item is specified in it. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA020 |
The specified data type is invalid. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA021 |
The specified access type is illegal. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA022 |
The specified data type is illegal. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA023 |
The no. of data you specified is too many to write.(Please reduce it to **** or fewer.) |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA024 |
The operation result to write is below the lower limit value. |
试图写入一个超出范围的值。请更改设置以写入一个范围内的值。 |
RYAA025 |
The operation result to write is beyond the upper limit value. |
试图写入一个超出范围的值。请更改设置以写入一个范围内的值。 |
RYAA026 |
Could not send processing request to the network destination due to insufficient memory. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA027 |
The specified group was not found. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA028 |
The two compared access tickets differ in their nodes, equipment, or devices. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA029 |
The specified access ticket is not for this node. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA030 |
Could not register the cache because of insufficient memory. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA032 |
The access ticket you tried to use in block access is not of the block type. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA033 |
The small service to process was not found. |
发生致命错误。重新执行传输。 或者执行GP-Pro EX强制传输。然后重新执行传输。 |
RYAA034 |
The size of block access to the device exceeded the limit. |
用于设备块写入/读取的最大缓冲区大小是10KB。请设置一个小于该限制的大小。 |
RYAA035 |
A different network project is being used. |
请使用GP-Pro EX再次传输工程文件。 |
RYAA037 |
The no. of requests/the buffer size of requests to Read/Write via network at a time exceeded the limit( **** ). |
请重新检查从GP-Pro EX到网络目标的请求设置，并重新设计系统，将请求数量限定到最大值以内。 |
RYAA048 |
A communication error occurred during communication with the destination node.Please confirm that the network connection to the node has been properly established. |
检查人机界面和目标设备之间的网络和电缆是否正确建立和连接。 |
RYAA049 |
The destination node did not respond within the specified time.Please confirm that the network connection to the node has been properly established. |
客户端的响应未在为该客户端设置的超时范围内。 |
RYAA050 |
The destination node did not respond within the specified time.Please confirm that the network connection to the node has been properly established. |
服务器的响应未在为该服务器设置的超时范围内。 |
RYAA051 |
Communication with the destination Node stopped because the destination or local Node closed. |
对连接到Run画面的人机界面进行设置。 |
RYAA064 |
Failed to read the device. |
数据可能已被读入非法或未定义的寄存器地址。请指定正确的寄存器地址。 |
RYAA065 |
Failed to write the device. |
数据可能已被写入非法或未定义的寄存器地址。请指定正确的寄存器地址。 |
RYAA069 |
The specified request is not supported. |
请通过传输系统将GPProEX升级到一个支持的版本。 |
RYAA070 |
The specified request is not supported. |
请通过传输系统将GPProEX升级到一个支持的版本。 |
RYAA080 |
The project ID of the network project file is different.(A different network project is being used. |
请使用GP-Pro EX再次传输工程文件。 |
RYAA081 |
The network project file does not have necessary data. |
请使用GP-Pro EX再次传输工程文件。 |
RYAA082 |
The network project file is damaged. |
请使用GP-Pro EX再次传输工程文件。如果还不能解决问题，请使用GP-Pro EX再次传输工程文件。 |
RYAA083 |
The network project file does not exist. |
请使用GP-Pro EX再次传输工程文件。如果还不能解决问题，请使用GP-Pro EX再次传输工程文件。 |
RYAA090 |
Unable to connect to server.Exceeding client limit. |
终止已经连接的GP-Viewer EX，并尝试再次连接。 |
RYAA091 |
Unable to connect to server.Server settings have changed. |
尝试再次连接服务器。 |
RYAA092 |
Unable to connect to server.Server authentication failed. |
尝试再次连接服务器。 |
RYAA093 |
Unable to connect to server.Server is starting up. |
尝试再次连接服务器。 |
RYAA096 |
Failed to transfer data to display unit.(****) |
请确认连接到人机界面的PLC工作正常。请使用GP-Pro EX再次传输工程文件。 |
RYAA097 |
Failed to read the device from display unit. |
试图访问读保护区。请更改设置避免此问题。 |
RYAA098 |
Failed to write the device to display unit. |
试图访问写保护区。请更改设置避免此问题。 |
RYAA099 |
In device access to the display unit, the device number was out of range. |
指定了无效寄存器。试图访问不存在的寄存器。 |
RYAA100 |
Failed to transfer data to display unit.(The destination Node does not respond.) |
目标节点未响应。检查如下内容：
请使用GP-Pro EX再次传输工程文件。 |
RYAA101 |
Failed to read the device from display unit. |
目标节点未响应。检查如下内容：
|
RYAA102 |
Failed to write the device to display unit. |
目标节点未响应。检查如下内容：
|
RYAA103 |
Operation was interrupted because the display unit was not online anymore. |
由于人机界面在线状态结束，正在进行的进程被中断。要完成该过程，请将人机界面设置为Run画面，并重复该过程。 |
RYAA112 |
Failed to update SRAM data. |
用GP-Pro EX强制传输系统。 |
RYAA113 |
No accessing SRAM while processing. |
用GP-Pro EX强制传输系统。 |
RYAA114 |
Unsupported request was set when accessing SRAM. |
用GP-Pro EX强制传输系统。 |
RYAA115 |
Could not retrieve SRAM data because of insufficient memory. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA116 |
Could not register periodical SRAM update because of insufficient memory. |
请关闭另外一个应用程序或重启操作系统。 |
RYAA125 |
Screen changes are not permitted from the client. |
画面切换请求被拒绝。检查如下内容：
|